3 Reasons for Your H20 Error in Your GE Dishwasher! (Simple fixes) 2023 (2023)

General Electric dishwashers are popular for two main appliance characteristics: their ability to produce great quality appliances and beautiful designs.

These designs also come with an efficient error detection system that comes to your attention when there are problems like the dishwasher error H20.

However, after spotting the error code, you might experience some difficulty in interpreting the code.

Therefore, you need to determine the meaning of the error in order to identify the cause of the problem and immediately fix it.

If you experience the error code H20 on your GE dishwasher, it indicates that the machine is not getting enough water or not getting water into its chamber. This problem usually means that your water supply is compromised, your water intake hoses are faulty, or you've opened your valves halfway. To correct the code, check the water inlet valve and hose for faults.

In this article, you will understand the H20 error code, what causes the error to appear on your display panel, how to clear the code and fix its causes.

You will also get a preview of other error codes and their meanings.

What does the H2O error code mean on my GE dishwasher?

If your GE dishwasher displays an H20 error code, it indicates that not enough water is flowing through the washer chamber. Appears when no water enters the dishwasher.

This no water issue usually occurs due to various underlying issues like bad water inlet valve, bad inlet hose, incorrectly opened valve or dysfunctional water supply.

However, if the error code appears on the1 hour wash cycle, you should contact a professional to repair the dishwasher.

If it appears in other wash cycles, a careful inspection of the water source and inlet valve will clear the error codes and help you identify the cause.

Also, the H20 error code often appears:

• If you have recently purchased the dishwasher,

• You are running the device for the first time,

• If you have recently repaired your plumbing,

• You recently cut off the water supply.

The following are the underlying causes of the H20 error code on your GE dishwasher:

#1.faulty inlet valve

The water inlet valve controls how much water fills the dishwasher and the timer controls it. It's faulty if it doesn't respond when you turn on the timer.

Open the bottom access panel to locate the inlet valve and verify that it works.

Also, if the inlet valve does not have enough water pressure, your inlet valve could be the cause of the error code being displayed.

#2.Defective or twisted hose

If the inlet hose is faulty, it will not allow enough water to flow into the dishwasher's chamber, hence the H20 error code.

The error code display can also be caused by a kinked or kinked hose. In this case, the hose will restrict the flow of water into the chamber due to its incorrect placement.

#3.badly open valve

If you recently turned off the inlet valve, make sure you turned it on correctly. You may have opened it halfway, decreasing water flow pressure.

In addition to these common issues, it is possible that your GE dishwasher is displaying an H20 error code due to other issues such as:

• A faulty circuit board or

• A problem with the main water supply.

So, before trying to fix the error, make sure you fully understand thesource of the problemto avoid further unnecessary complications.

In addition to the H20 error code, there are other error codes that you may need help deciphering on your display panel.

The following table shows some common GE error codes and what they indicate.

How do I fix the H2O error code on my GE dishwasher?

To correct the error code on your GE dishwasher, locate the inlet valve next to the dishwasher and ensure it is fully ON. Check the inlet hose for connections or faults and correct them.

If the problem is not with the appliance, check the main water supply, it may be cut off or not fully open. Once you've detected the cause of the error code display, fixing it won't be a problem.

Here are some solutions to fix and clear your GE dishwasher H20 error:

#1.Replace faulty inlet hose

The inlet hose connects the water inlet valve to the dishwasher chamber, allowing water to enter.

However, when the plumbing fails, it reduces the water pressure and activates theError code H20.

To correct this problem, locate the inlet hose and inspect it for damage and failure. If the hose is defective, replace theinlet hose.

#2.straighten kinked hose

If so, your hose could be in the wrong position, causing it to bend and restrict the flow of water from the main water source.

#3.Inspect the water valve

If the above solutions don't work, the water inlet valve could be the problem. However, to confirm the functionality of the inlet valve, you must inspect it.

Follow the steps below to examine your inlet valve:

• Disconnect your dishwasher from the power supply and turn off the water source.

• Check the bottom left of your dishwasher to locate your machine's water inlet valve.

• It may be necessary to open the bottom access panel to access it.

• Inspect the inlet valve for cracks, wear, or any signs of damage. If you detect any on the inlet valve, replace theintake valve.

In addition to the above solutions, you can try the following tips to clear the dishwasher error code:

• Make sure the washer is not tilted to one side. Sloping can lower the water level on one side of the washer chamber, triggering the error code.

• Choose a different cycle mode and reselect the previous wash cycle.

If the problem persists after trying the above solutions, make an appointment to have a professional repair your washing machine.

How do you reset error codes on a GE dishwasher?

You can reset error codes on GE dishwashers by unplugging the power supply, entering service mode, or pressing the start button.

The required reset method depends mainly on your device model, the type of error code and the location of your control panel.

While resetting the washer is a good solution for clearing error codes, it should be a last resort to correct any error codes.

Here are the various ways to perform a reset on your dishwasher:

#1.Enter service mode

Most GE dishwasher models have a service mode that you can activate to restart the washer. The mode also helps you to run tests for iidentify the cause of the error codein your dishwasher.

To activate service mode on your GE dishwasher:

• Press and hold the Cycle Select and Start buttons for about five seconds.

• Then hold Select Cycle again for five seconds. This action will activate the lock button.

• Then press the Home button again for about five seconds. This action will cause the Home button to blink repeatedly.

• Finally, repeat the first step to restart the dishwasher. This action will activate the control panel light and restart the dishwasher.

#2.Power supply disconnection

This method resets the dishwasher by draining the dishwasher's electrical charges.

To disconnect the power supply, disconnect the dishwasher from the power supply. Wait 30 seconds before turning it back on.

#3.Double tap the home button

This reset method is suitable if your GE dishwasher is on but not running. To restart the dishwasher, press the Start button twice. This action will restart the cycle.

Conclusion

If the error code H20 is displayed on the control panel, this indicates that the dishwasher chamber is not receiving enough water during the wash cycle.

Once you see this error code, check your water supply, water inlet valve, or inlet hose to see if there is a problem. As soon as you discover a fault that you cannot repair, contact a specialist to repair the washing machine.

References;

• https://productos.geappliances.com/
• https://homeguideinfo.com/
• https://tigermecanico.net/
• https://productos.geappliances.com/